43 Amplifi ers & Accessories 700 Watt HF Linear Amplifier As long as the VSWR stays below 3:1, this amplifier lets you change between the 160 and 10 meter bands without using an external tuner. The A1010 can withstand up to 240 watts of reflected power, up to 100 milliseconds of drive spikes and deep voltage drops. Its durability and front-panel controls make this amplifier an excellent choice. All ACOM 1010 amplifiers come with either pre-wired 120VAC or 240VAC plug, installed and tested at DX Engineering. AOM-1010-120 ACOM 1010 with Pre-Wired 120VAC Plug .........................$3,376.99 AOM-1010-240 ACOM 1010 with Pre-Wired 240VAC Plug .........................$3,376.99 1,500 Watt HF+6M Linear Amplifier Enjoy the ACOM 1500's HF+6M coverage; low distortion and noise figures; fast and easy adjustments with its large, smooth knobs and sleek LCD screen; three antenna outputs; nearly silent input bypass and antenna relays; and diagnostic data stored in one of seven nonvolatile memory banks. All ACOM 1500 amplifiers come with pre-wired 240VAC plug, installed and tested at DX Engineering. AOM-1500-240 ACOM 1500 with Pre-Wired 240VAC Plug ....................... $5,122.99 1,000 Watt HF+6M Linear Amplifier Easy to operate and easy to maintain, ACOM’s 1000 is an extraordinary good value for HF operators. You can switch bands without a tuner, provided VSWR stays below 3.1. That gives you an edge during a contest scramble. Broadband input matching means that your radio will always see a very good load across the entire 1.8-54 MHz spectrum. Specially mounted relays deliver virtually silent QSK operation. This amplifier can also withstand significant amounts of reflected power and signal fluctuations. All ACOM 1000 amplifiers come with either pre-wired 120VAC or 240VAC plug, installed and tested at DX Engineering. AOM-1000-120 ACOM 1000 with Pre-Wired 120VAC Plug ................................$4,364.99 AOM-1000-240 ACOM 1000 with Pre-Wired 240VAC Plug ................................$4,364.99 eBox Ethernet Remote Control Devices The easy-to-operate eBox is an active Ethernet device which directly integrates ACOM power amplifiers to the Ethernet networks. These units have been specifically designed for remote control use with the ACOM 600S, 700S, 1200S, and 2000A with Remote Control Unit (RCU). The eBox receives specific commands via a web browser-based, user-friendly interface and forwards them to the ACOM amplifier. The eBox is compatible with all popular operating systems and web browsers (Chrome, Opera, Firefox, MS Edge, Safari, et. al.). Universal wall supply with Euro-US plug adapter included. AOM-EBOX-2000-P eBox with Cable for ACOM 2000A with RCU ............................$757.98 AOM-EBOX-SS-P eBox with Cable for ACOM 600S/700S/1200S .........................$757.98 1,500 Watt HF Linear Amplifier The user-friendly 2100 uses a powerful tuning aid and automatic input attenuator to let you quickly match the input impedance to the tube load impedance. As long as the VSWR stays under 3:1, you won't need an antenna tuner. A good choice for Field Day, EMCOMM and base stations, the 2100 is packed with self-protection features and will withstand up to 400 watts of reflected power. It boasts intuitive controls and OLED display for straightforward operation. Order the AOM-2100 model to wire the AC plug yourself; order the AOM-2100-240 for pre-wired 240 volt operation, tested by our techs. All ACOM 2100 amplifiers come with pre-wired 240VAC plug, installed and tested at DX Engineering. AOM-2100-240 ACOM 2100 with Pre-Wired 240VAC Plug .......................... $5,687.98 500 Watt 160-4M Linear Amplifier With output power of 500W (PEP or Digital) and coverage from 1.8 through 70.5 MHz, this user-friendly, compact (11.5" W x 6.2" H x 10.6" D), and lightweight (17.20 lbs.) RF power amplifier is great for DXpeditions and field ops. The built-in switching-mode power supply operates with an extended mains voltage range of 100-240VAC, with no internal switch over. A rugged LDMOS transistor and broadband input circuit present an SWR below 1.5 without retuning throughout the frequency range. Features include two antenna outputs, intelligent protection circuits, frequency filters that exceed EMC requirements, and integration with ACOM 04AT/06AT tuners. Note that 4M operation is not authorized in the U.S. and many other countries. Legal operation is the responsibility of the user. All ACOM 500S amplifiers come with either pre-wired 120VAC or 240VAC plug, installed and tested at DX Engineering. AOM-500S-120 ACOM 500S with Pre-Wired 120VAC Plug .........................$3,854.99 AOM-500S-240 ACOM 500S with Pre-Wired 240VAC Plug .........................$3,854.99 1,000W HF+6M Linear Amplifier With less than 80W input, the ACOM 1003 delivers 1,000W PEP output or 900W continuous carrier using a single ceramic/metal power triode (3CX800A7). The model features two new front panel relay switches—one to select from three antenna outputs and another to quickly engage and disengage an input attenuator for rapid tuning without transceiver adjustment. Among its many advanced features is a True Resistance Indicator bar scale meter that simplifies accurate adjustment of plate-load impedance controls. All ACOM 1003 amplifiers come with either 120VAC or 240VAC pre-wired plug, installed and tested at DX Engineering. AOM-1003-120 ACOM 1003 with Pre-Wired 120VAC Plug .......................$4,899.99 AOM-1003-240 ACOM 1003 with Pre-Wired 240VAC Plug .......................$4,899.99 1400S Solid State 1.8-54 MHz 1,200W Linear Amplifier The ACOM 1400S-240 version achieves 1,200W output power, PEP, or continuous carrier. The 1400S-120 version for 120VAC operation achieves 600W output power, PEP, or continuous carrier. The 1400S Remote Control Unit's (RCU) edge-to-edge color touchscreen provides an information display and amplifier operation on the desktop. Designed for simplified operation, the 1400S's RCU menus are intuitive and easy to follow, and no special skill is required when changing frequency bands. When connected to a transceiver with CAT capability, the amplifier tracks the operating frequency and changes bands automatically. Even when not interfaced to CAT, the amplifier monitors the input signal frequency through the built-in frequency counter and automatically switches bands. All ACOM 1400S amplifiers come with either 120VAC or 240VAC pre-wired plug, installed and tested at DX Engineering. AOM-1400S-120 ACOM 1400S Amplifier w/Pre-Wired 120VAC Plug, 600W......................................................................$6,074.99 AOM-1400S-240 ACOM 1400S Amplifier w/Pre-Wired 240VAC Plug, 1,200W ..............................................................$6,074.99 WARNING: For Proposition 65 information, see p. 3 Visit DXEngineering.com for the latest limited-time of ers and special savings!
